Luxury Ceramic Bathroom Toilet 660x370x740mm One Piece WC Toilet Price

Product Description
Specifications
Leading Exporters of Bathoom Sanitary Ware
Brand " LYCOS"
Wide Range & Best Quality
Attractive Price
Timely DeliveryTechnical SpecificationsSpecifications of 'LYCOS SANITARY WARE' Products CharactristicsIS 2556-1-1994LYCOS' Test ValueSurface BlemishShould conform to NormsIn conformity with the NormsWater Absorption %0.5 Max. Mean Value0.1 Max. Mean ValueModulus of rupture (M.O.R.)60 Mpa Min. Mean Value70 Mpa Min. Mean ValueCrazing Resistance 0.34- 0.37 Mpa10 Hrs. Min.20 Hrs. Min.Chemical ResistanceShould Conform to NormsIn Conformity with the NormsStaining & Burning ResistanceShould Conform to NormsIn Conformity with the NormsINSTALLATION & MAINTENANCE TIPSInstall Wash Basins with or without pedestals on CI Bracket with Rag Bolts. If wash basin is Large in size install on pedestal screwed to the floor.Install wall mounting E.W.C. With the help of CI chair.Install Floor Mounting E.W.C. Screwed to the floor.Avoid using Cement at the hollow bottom portion of E.W.C.Regular Cleaning with dry cloth / Mild Detergent is recommended to avoid stains & if required diluted Hydrochloric acid may be Used.Do not use hard bristled brush for cleaning so as to avoid scratches.Your Trouble-Shooting Guide(FOR GOLD - TYPE FITTINGS)At Ceramics Division, LYCOS Ceramics, it has been our endeavour not only to provide you with the best possible service, but also to help you serve your customers better. We have been analysing the complaints received by us and have discovered that most of the complaints fall into a pattern. We would like to share the qualitative results of the analysis with you, so that you can be better prepared to handle any complaints received from your customers.For each problem faced, the probable causes are explained. Alongside, you can find the corrective actions required to solve these problems. We hope that you would find this trouble-shooting chart useful. You could apply this for suites as well as wallvit pansFlushing Test1 Toilet Paper TestThe water closet shall be filled with water to its normal water seal level and charged with six pieces of usual toilet paper or polythene sheet of 0.05 mm thickness approximately 150 mm x 115 mm in size and loosely crumpled. It shall then be flushed. This test shall be repeated four times and the pan shall discharge the full charge of the paper at last three out of four times.2 Smudge TestThe whole of the interior surface of water closet to 40 mm below the flushing rim shall be smudged with quartz powder of contrasting colour passing through 1.18 mm IS sieve and shall then be flushed observing carefully the surface of the water closet during the flushing. Immediately after the flushing, there shall be no smudge left on the bowl.3 Holding Capacity TestThe water closet when sealed at the outlet and vent (if fitted) with water-tight seal shall be capable of holding not less than 10 1 of water between the normal water level and the highest possible water level of the water closet as installed.4 Ball TestSingle Ball Test :The ball shall be made of non-absorbent material. The relative density of the ball shall be between 1.075 and 1.080. The diameter of the ball shall be 43 ± 0.5 mm. Place the ball into the water closet to be tested and then flush the water closet. The ball shall be discharged in the normal manner. The outlet (trap) of the water closet goes into the floor.The outlet (trap) of the water closet goes into the wall.5 Fifty Ball TestFifty balls of non-absorbent material, having a mass each of 3.7 ± 0.1 g, and a diameter of 20 ± 0.1 mm
shall be dropped into the water closet bowl and flushed. Repeat the test five times. A minimum of 85
percent of all balls should be flushed out in the five tests.6 Load Bearing Testforce of 4 + ° .05 kN shall be applied for period of one hour by placing it on a wooden beam with a cross
section of 100 mm x 100 mm positioned across the centre of the opening of the top surface of the WC.
There shall be no damage or defect which shall occur to the WC.7 Saw Dust TestSpecification of the Saw Dust 20 g of dry saw dust test sifted through 2 mm sieve.
Procedure: Set up the WC, cistern or flush valve and flush pipe (if required) as specified by the
manufacturer. Charge the WC with water to its designed water seal level. Fully wet the entire internal
surface of the WC below the rim. Sprinkle 20 g of fine dry saw dust of above specification on the inside of
the WC between the normal water level and the flushing rim as completely and evenly as possible. Then
flush the WC. The sprinkle saw dust should be cleaned below 40 mm of rim of WC.8 Splash TestProcedure: Set up the WC, cistern or flush valve and flush pipe (if required) as specified by the
manufacturer. Charge the WC with coloured water to its design water seal level. Ensure that the floor area
is cleaned and dry where the splash test to be carried out. Activate the flush valve or cistern to the
discharge the WC. Observe and record whether flushing water splashed over rim onto the floor. Repeat
the test 5 times. Record whether the flushing water splash over the rim onto the floor. Isolated droplets up
to 10 Nos., shall not be the cause for rejection. Problem facedProbable ReasonsCorrective ActionTank is
shakingExpansion plug may not be correctly
fixed in the tank's fixing hole provided
towards the back of the closet.Fix the expansion plug provided.Tank holding screw may not be
tightened fully.Tighten the tank holding screw evenly till it cannot
be tightened any further with one hand.Continuous leakage of
water from the cisternArm may be fixed in a wrong
direction.Fix the arm such that the shorter arm side is
facing the front of the cistern.Valve ring may not be fixed properly
to the bottom of the body.Fix the valve ring to the top of the groove
provided in the body. Ensure that the
valve ring sits securely around the groove.Valve ring may have cracked or
could be worn out.Replace the valve ring.Lifting rod and floating body
assembly may not be perpendicular.Adjust the bracket so that its center hole aligns
with the hole provided in the lid of the cistern.Lifting rod and floating body assembly
may not be guided through the guide hole
provided in the bottom of the valve seat.Guide the lifting rod through the hole
provided in the bottom of the valve seat.Cistern not fully tightened to the closet.Tighten tank holding screws evenly till they cannot
be tightened further with one hand.Discharge of
water stops
abruptly when
the flush knob is
pulled and
releasedWater may be overflowing through
the floating body.Turn the adjusting screw provided on the top of the
inlet in the anti clockwise direction. Reduce the
water level such that the water level shuts off
below the 'over-flow' level.Buoyancy may not be created for the
floating body.1. Push stop dog (black rubber tube) which is
fixed to the lifting rod such that top end of the
stop dog touches the bottom of the lifting bar.2. Adjust the lifting bar such that the hole
provided near the top-end threaded portion of the
lifting-bar is just visible over the lid screw
(when observed in assembled condition).Water does not
enter the cistern
through the inletThe inlet may be in the fully closed
position.Turn the adjusting screw provided on the top of the
inlet in the clockwise direction to open the inlet.Water line may be choked.Ensure periodical cleaning of water
tank and water lines.Water quantity
insufficient for
effective flushingFloat ball height adjusted to lower
quantity of water discharge.Turn the adjusting screw provided on the top of the
inlet in clock wise direction to increase the discharge
level. (Caution: The water level may be increased till
the water from the inlet shuts off at the 'top-line'
mark provided on the floating body).Water leakage
observed between
cistern and closet
during flushing.Water divider may not be properly
fixed.Fix the water divider such that the 2 weep holes
provided in it face each other after installation.
Ensure that the inlet of the water divider is
passing through the outlet of the valve-seat fullyContinuous innovation and improvement in manufacturing techniques and products are carried out regularly. We reserve the right to supply articles which may not correspond exactly with the particulars given in this booklet.Packaging & Shipping
Packed in 5 Layer Export Quality Corugated BoxOur ServicesQuick and Efficient reply within 24 hours After receiving contact.We accept OEM/ODM service.Sample order will be available.Confidentiality: Business between us will be confidential to any third partyOver 10 Years experience in manufacturing one piece toilet, two piece toilet, pedestal basin, urinal, counter basin, wall-hung basin,bidet and bathroom accessories and so on.Service Parts availableOffices available in India, Nepal, China, Hongkong, Thailand, UAE and SingaporeCompany Information
Dear sir,
It is our pleasure to introduce our company Lycos Ceramic Pvt.Ltd.
Our factory located in Morbi, state of Gujarat-India.
We are leading manufacturer and exporter, of Ceramic Tiles, porcelain tiles & Sanitary ware since many years.
Likewide range of Digital Inkjet Wall and Floor Tiles, Rotocolor Wall &Floor Tiles, Polished Porcelain Tiles, Glazed Porcelain Tiles, Ceramic Wall & Floor Tiles, Designer Tiles, Exterior Tiles and all kind of sanitary wares.
Lycos truly believes in quality ethics. All items manufactured by the group are ISO certified.
Our website is: www.lycosceramic.com
Our e-catalogs and specifications for all different sizes available on website.
Lycos supplies ceramic & porcelain wall and floor tiles with sanitary wares to Europe, Latin America, Middle East and African countries since many years with AAA+ grade quality and good quantity. We use high technologies and best row materials and always ready stock for all product so customers get best services with quality. Our main aim is customers satisfaction because Lycos always with customers and accept customer demand like designs and OEM.
If you start the good business with Lycos then no need to find any new suppliers because Lycos don’t want only business but develop best relationship with our all customers for do long term business.
We assure you to good business relation and best co-operation from our end.
Awaiting for your prompt Reply…

Thanks !!
Raj patel.
(Export Head)
Mail id : export.lycoscera[at]gmail.com
msn id : lycos.raj[at]live.com
Skype id : ronaksurani
Mobile : +91 787 4144141,+91 99099 98712. (Whatsapp)
www.lycosceramic.com
LYCOS CERAMIC PVT.LTD.
------------------------------------