spray thermosetting polyester spray paint and powder coat paint

spray thermosetting polyester spray paint and powder coat paint
1. Our Powder Coating Advantage:
(1) Spray ratio is 90%;
(2) 1KG of powder coating can spray 8-10 square meter;
(3) Powder Coating adhesive force is stronger 8-10 years;
(4) Powder Coating is not easy to fade in 5-8 years;
2. Charactcristic: Powder Available Powder TypesAvailable Colors1. Epoxy powder coating1. RAL Colors2. Polyester Powder Coating2.Pantone Colors3.Epoxy-Polyester Powder Coating( Hybrid)3.Customer color matching4.Polyurethane Powder CoatingAvailable finish5.Heat transfer printing powder coating1. SmoothAvailable gloss level2. Rough( Sand texture )1. High gloss( Above 80%)3.Wrinkle( fine texture )2. Flat gloss (50%-80%)4.Antique( hammer tone)3. Semi gloss(5%-50%)5.metallic4. Matt ( below 5%)6.Other special effect ( artistic)
3.usage Application Area1. Household Applications7. Used for Security Door;2. Car Coating8. Radiator & Heat Sink;3. Used for Valve9. Corrosion Prevention of Pipes;4. Track Traffic10. Communications Equipments;5. Aerospare field11. Hardware & Brightwork;6. Fitness Equipment12. Zincing & Aluminium;
Company Information
Contact Information:
TEl: 86-523-88686808;FAX:86-523-88582696;
Cel: 86-13775795436;Skpye: betty551860;
Wechat: 86-13775795436;
Website: www.jsfuruida.com;
www.jsfrd.cn
Http://florid2004.en.alibaba.comPackaging & Shipping
Carton Size: 39CM*34CM*35CM, 25KG/Carton or
20KG/Carton; 0.05CBM/Carton;

PalletSize: 1M*1.2M,1000KG/Pallet;1.2CBM/Pallet;Our Services
1. We offer professional products and fast delivery.
2. We will help you solve problems when you use our products.
3. Any question can turn to the technology department of our company.FAQ Bad symtomsPossible Cause Solution
1.With low power, powder
coating is not easy to coated;1.High voltage power supply shortage;1.Check the circuit 2.Grouding is bad;2.Remove clutter grouding line
3.Compressed air volume is too big,
the powder to blow fell &blows away;
3.Spray appropriate isolation,
reduct air convection;4.Powder particle size is too thin;
4.Add new powder coating, reduce the
recovery powder consumption.5.The air temperature is too high;
5.Powder particles with air water
branch of low power, control
temperature of spray area;
2. Charge repulsion powder
repboud from the working
surface;1.The voltage is too high;1.Lower voltage and air volume;
2.Spray gun from the work location is
too close;2.Extend the spray gun and artifacts;3.Grouding is bad;3.Remove clutter grouding line;
4.Powder particle size is too thin, not
esay to attach to the workpiece surface;
4.Add new powder coating, reduce
the recovery powder consumption;
3. Corner not easy spraying
penetration is bad;1.The powder amount is too small;
1.Lower voltage and air volume,
increasing the amount of powder;2.Grouding is bad;2.Adjust the spray gun position;3.The voltage is too high;3.Choose small backboard, proper nozzle;4.Spray gun position is not good;
4.If the corner is more and deeper, then
consider friction gun equipment;5.Powder spraying range is too wide;4.Powder spraying uneven1.Air pressure is insufficient;1.Cleaning pipeline, spray gun and flowmeter;2.Line fault block;
2.Check the air supply, Exclude water vapor
in powder agglomeration;3.Block in the spray gun;
3.If powder agglomeration, to screen or
change new powder coating;