CNC Servo Drive HCNC HSV-180UD Servo Motor Amplifier for Lathe and Milling Machine

Product DescriptionProduct Paramenters
Servo drive unit specifications
Adapted motor power (KW)
Rated output current (A)
Max. short-time current (A)
HSV-180UD-035
3.7
12.5
22
HSV-180UD-050
5.5
16
28
HSV-180UD-075
7.5
23.5
42
HSV-180UD-100
11
32
56
HSV-180UD-150
15
47
84
HSV-180UD-200
30
64.3
110
HSV-180UD-300
37
94
168
HSV-180UD-450
51
128
224
Input power supply
HSV-180U-150 and below: three-phase AC380V, -15% to +10%, 50/60Hz
HSV-180U-200 and above:
1. two-phase AC220V control power supply, -15% to +10%, 50/60Hz
2. three-phase AC380V, -15% to +10%, 50/60Hz
Environmental condition
Temperature
At operation: 0 to 40 degrees (condensation free)
Storage: -20 to 60 degrees
Humidity
Below 90%RH, condensation free
Altitude
Below an elevation of 1000m
Vibration
Less than 20Hz, 4.9m/S²; 20 to 60Hz, 1m/S²（no continuous use at resonant frequency）
Control mode
IGBT PWM mode, sine wave drive
Motor encoder
Serial port
Sine cosine absolute encoder, with the subdivision of 17Bit
All digital serial absolute encoder
EnDat2.1/2.2 protocol, HiperFACE protocol, TAMAGAWA protocol
A/B phase
General composite incremental encoder, differential input of A/B/Z signal and U/V/W signal (RS422 level)
External encoder
Serial port
Absolute value feedback, EnDat 2.1/2.2 protocol
A/B phase
Differential input of A/B/Z (RS422 level), 1Vpp sine cosine signal
Control signal
Input
Enable, reset, trigger signal, users specified
Output
Alarm, users specified
Communication function
RS232
1:1 communication which is used to connect to upper computer
Ethernet bus
NCUC bus communication protocol
Front panel
Five buttons, six 8-SEG LEDs (combination readout), two LEDs
Regenerative brake
For the type below 75A: mandatory built-in regenerative brake resistor, and optional external brake resistorControl mode
5 alternative modes based on parameter setting: position control, velocity control, torque control, position/velocity control(mode switching), all closed-loop control
Monitoring function
Speed, current position, position deviation, motor torque, motor current, command pulse frequency, running state, etc.
Protection function
Hard failure
Overvoltage, undervoltage, motor overheating, overcurrent, encoder failure, abnormal network communication, etc.
Soft failure
Excessively large position deviation, excessively large speed deviation, overspeed, overload, EEPROM failure, etc.Company Profile
Wuhan Huazhong Numerical Control Co., Ltd. (Hereinafter refered to as HCNC) was established in 1994 with a registered capital of 172,79 million yuan and its history could be dated back to 1950s. HCNC is a high-tech enterprise which specilizes in R&D, production, sales of CNC system, industrial robot, infrared themal imager, new energy vehicle. HCNC was successfully listed on the GEM with Stock Code 300161 in 2011. HCNC was granted one of national first batch of 91 Innovative Enterprises by Ministry of Science and Technology and State-owned Assets Supervision and Administration Commission of the State Council.
Contact Us
Wuhan Huazhong Numerical Control Co., Ltd.
HUST Park, Miaoshan Region, East-lake high-tech zone, Wuhan, Hubei, China.
Mobile: +86-18301189551
Email: zhouwuhui2@hzncc.com
Web: http://www.huazhongcnc.com