Professinal HSS Annular Cutter Core Drill HSS Cutting Tools For Magnetic Drill Press

Product Description

Professinal HSS Annular Cutter Core Drill HSS Cutting Tools For Magnetic Drill Press

1. Annular cutter made of high quality high speed steel to increase the endurance of cutting edges;

2. Multi-cut geometry for ply-cutting to improve performance of centering as well as removal of chips;

3. Various shank type are avaliable to suit various brand magnetic drills, weldon shank, universal shank, fein quick-in shank etc;

4. Regular diameter 12mm to 65mm, with 8mm, 25mm, 35mm, 50mm, 75mm, 100mm cutting depth. Other sizes can be customize.

Products Show

FAQ

1. What causes annular cutters to break or dull prematurely?
The primary cause of broken or prematurely dull cutters is a feed rate that is too slow. Slow feed rates will reduce the life of your cutter. Using a firm, steady feed pressure throughout the cut will maximize performance and extend tool life.2. Why do I have to clear chips from the cutter before every cut?
As the cutter begins removing material, new chips flow out through the gullets and up the flutes. If these pathways are not cleared before cutting a new hole, packing or binding may result, causing the cutter to fill with chips and possibly break. Because annular cutters are hollow, there is no dead-zone resistance to overcome. All cutting edges are located near the periphery of the tool, and surface speeds are consistent throughout the entire cut.3. When do I use a magnetic drill?
It can be time-consuming and cumbersome to try to jockey a large pipe into position at a stationary drill press or work center. A portable magnetic drill allows you to take the drill to the workpiece, instead of trying to bring the workpiece to the drill. A portable magnetic drill press also may be used in any position-vertical, horizontal, or overhead. The workpiece must be at least 3/8 inch thick.4. Is the magnet on my portable drill press strong enough to drill pipe?
When you're using a portable drill press, a support system is needed. A safety chain or strap is also recommended, in case the magnet slips from the support. When you are using a magnetic drill and pipe adapter accessory, mount the adapter securely to the pipe with a tightly wrapped chain (see lead image). Make sure the support system for the drill arbor is rigid and in good condition.5. How do I keep my magnetic drill from slipping?
Make sure the drill's magnetic base is clear of chips and debris and is securely attached to a clean workpiece. Uneven surfaces or large debris buildup prevents the magnet from obtaining optimal holding power, which can cause the drill to shift or lift during operation. A safety chain or strap also helps to prevent injury if the drill shifts. If it does shift or lifts during the cut, and the motor is not stopped, the cutter will break. A good magnetic drill will have a built-in safety circuit that stops the motor immediately when the drill lifts from the material. 6. What is the purpose of coated cutters, or cutters made from premium steel?
Cutters made from M2 high-speed steel (HSS) are recommended for materials with a Brinell hardness number (BHN) of up to 275. A titanium nitride or similar coating may be applied to M2 to fortify wear resistance in materials up to 325 BHN. For materials up to 350 BHN, cobalt steel (M35) is recommended with a titanium nitride or similar coating.7. What makes the slug stick in the cutter?
Using lubricant or cutting fluid helps the slug to eject at the end of the cut. But when slug ejection becomes unreliable or the tube resists cutting, it probably means the cutter's cutting edges are becoming dull. Resharpen or replace your cutter.8. Is coolant necessary?
Always use some form of coolant when drilling to maintain cutting performance and tool life. Any form of coolant or lubrication helps-even water works better than nothing at all.9. What happens when my portable drill press becomes loose or parts wear out?
For the best performance, always maintain your drill as instructed in the operator's manual. Many magnetic drills feature a slide/gib/way system that requires periodic adjustments to maintain rigidity and optimal performance. Worn or damaged parts should be replaced to reduce the possibility of injury.

Professinal HSS Annular Cutter Core Drill HSS Cutting Tools For Magnetic Drill Press