AAC products block machine,AAC,AAC block machine,

AAC blocks are made of fly ash,lime,cement and aluminium powder,and with the procedures of crush- ing, measuring, mixing, pouring, autoclaving and cutting. AAC block has advantages of extremely light weight, excellent thermal insulation, heat insulation, energy conservation,waste recycling,convenience etc. As a new building material, AAC is emphatically promoted by the world.autoclave aerated concrete products block machine,AAC,AAC block machine, The AAC factory drawing
AAC plant (AAC automatic plant ) First,Material HandlingJaw Crusher

Mainly used for compressive strength less than 320 MPa materials, with big crushing ratio, high yield, even gra- nularity, simple structure, reliable operation, easy maintenance, low operating cost. The crusher has been widely used in mining, smelting, building material, highway, railway, water conservancy and other departments. Work principle of Jaw crusher: When jaw crusher works, the motor through the belts driven eccentric shaft rotation, so that the movable jaw cycle close, leaving the fixed jaw, multiple break materials through squeeze, rub, grind the materials, then make the material into small whereabouts, until discharged from the discharge door.Ball Grinder
Ball grinder is used to grind a variety of ores and other mate- rials in the mineral processing, building materials and chemical industry. It can be divided into wet and dry two grinding types. According to the ways of discharging, it also can be divided into grid and overflow type.Beating Pool
Pouring materials into pool and modulated into slurry.. Silo
Silo is used for fly ash or slurry, with slow-speed mixing to avoid sedimentation. Silo over 100 m usually is designed with planetary type mixing.Second, Dosing And PouringMeasure
Measuring system is used to weigh each raw material.
Pouring Mixer
Pouring mixer is fixed on the top of mould whose function is to mix raw materials of slurry, cement, lime, gypsum and aluminum powder before pouring them into mould.Mould
Slurry could be held in the combining of mould and side plate. After curing it would be solidified into the semi-finished pro- duct. Mould size:4.2m,4.8m,6m.Side Plate
The side plate is used to load the semi-finished product which will be cut by cutting machine and fed into the au- toclave to be hardened together with the trolley.Curing Room
After pouring,use conveyor chain push mould into curing room under temperature 50-70 degrees. The curing time would be 1.5-2 hours.(according to favorable geographical condition, the step can be skipped.)Third,Tilting CutterTilting Hoister
Lift the poured and cured product together with mould and side plate up in the air, turn it over 90 degrees to keep the block upright, carry it to the cutting cart, open mould and lift away the mould so that the semi-finished product can be out. Then mount and clamp the side plate on the mould once again, turn it over 90 degrees and carry it back to the starting line so that pouring can be resumed.
Vacuum Hood
The vacuum hood can remove the scrap after cutting and to enhance the material utilization ratio.
Tilting Table
After block was cut, the tilting table turns it 90 degrees, and remove the waste that at the bottom of block, thereby im- proving the utilization of waste.
Semi-finished Product Hoister
After cutting, semi-finished product hoister hang product on the steam trolley by grouping.
Steam Trolley
The steam trolley is used for carrying the product with side plate pass in and out of autoclave. The cut product is ha- nged with side plate to steam trolley and be carried into autoclave for curing.Fourth,Finished-Product Out From Autoclave
Finished-Product Clamp
Carry the finished-product to packing line for making final package after autoclavedSeparator
The separator is used to separate the plaster block into pieces, in order to be transferred and used.Autoclave
Autoclave is a large pressure vessels used for steaming aerated concrete, sand-lime, fly ash brick or standard brick,the autoclave complete the hydrothermal reaction of CaO-SiO2-H2O. It is also widely used for other required pressure steam curing of the production project. Such as high-strength gypsum, insulation materials, rubber, high-strength glass, cement, pipe piles and timber, pharmaceutical, chemical and other industries. According to user requirements, our company can also design and manufacture of various forms of autoclave in order to meet the needs of the user a variety of purposes.