Combustion Equipment The Best Quality Combustion Equipment Catalytic Combustion Machine

Product DescriptionProduct Description
Main design parameters
Analysis of exhaust gas emission
1.1 Exhaust gas source: alkanes, alkenes, benzene alkene, alcohols, aldehydes, ketones, ethers, acid, college esters, phenols, halogenated hydrocarbon, mercaptan kind of exhaust gas.
1.2 Main ingredients of exhaust gas: exhaust propane, ethane, cyclohexane, ethylene, propylene, styrene, benzene, xylene, benzene, a college of methane total hydrocarbon, formaldehyde, acetaldehyde, acrolein, acetone, butanone, ethanol, ethylene glycol, isopropyl alcohol, ether, butyl ether, dimethyl ether, acetic acid, acrylic acid, ethyl acetate, propyl acetate, phenol, methylene chloride, chloroform, methyl mercaptan;
1.3 Exhaust gas volume: 5000-60000M³/H
1.4 Exhaust gas concentration: 300MG/M³
1.5 The exhaust gas temperature: 40 ℃ or less under normal temperature
1.6 Working time: 24H continuous operation
1.7 Design emission standards: in line with GB162897-1996 "comprehensive emission standards for atmospheric pollutants" level 2;
2.Process diagram

3 Adsorption gas process
Adsorption boxes made of carbon steel painted the wall outside the inner is equipped with a certain amount of activated carbon, and set up the high college temperature detection device, when the waste gas containing organic matter under the effect of fan, after activated carbon adsorption layer (in stacks), organic matter was activated carbon special forces trapped in its internal, clean gas comes out; After a period of time, when the activated carbon reaches the saturation state, the adsorption stops. At this time, the organic matter has been concentrated in the activated carbon. (the saturation time shall be calculated according to the original measured concentration, or the empirical value shall be set);
4 Desorption gas process
Catalytic purification device heating chamber inside, start heating device, into the inner loop, as the hot air to machine the boiling point of content, organic matter ran out from inside the activated carbon, into the catalytic chamber for catalytic decomposition into CO2 and H2O, release energy at the same time, the use of energy in adsorption bed again stripping, heating equipment stopped completely stop working right now, the organic exhaust gas catalytic combustion chamber on a spontaneous combustion, exhaust gas regeneration, circulation, until the complete separation from inside the activated carbon, organic matter and catalytic decomposition, got regeneration of activated carbon, organic catalytic points solution treatment; The heating device needs to be started for each clearance desorption, and the heating power is not needed for continuous desorption.
Catalytic combustion: organic gas is converted into harmless water and carbon dioxide gas at a lower temperature by using catalyst as an intermediate, that is:

5.The whole equipment technical performance and characteristics
5.1 The equipment has advanced design principle, unique material, stable performance, simple operation, safe and reliable, no secondary pollution. The equipment covers an area of small, light weight.
5.2 The use of a new type of activated carbon adsorption material - honeycomb activated carbon has advantages of thermodynamic properties, low resistance, low consumption, high adsorption rate, etc , compared with the granule (bar)
5.3 The catalytic combustor uses ceramic honeycomb noble metal catalyst, the resistance is small, can operate normally with the low pressure fan, not only consumes less electricity but also the noise is low.
5.4 Activated carbon bed adsorbing organic waste gas can be used for desorption and regeneration of the heat generated by the waste gas treated by catalytic combustion. The gas after desorption is sent to the catalytic combustion chamber for purification. No additional energy is needed.
6. Security measures
As the purification system deals with flammable and explosive gases, the following safety measures are taken to ensure the safe operation of the system:
6.1 Strictly control the concentration of exhaust gas "VOC" in the system below the lower limit of explosion by 1/5(about 10g/m3). It is completed by online concentration detector.
6.2 All system equipment and duct are well grounded to eliminate static electricity
6.3 The device is equipped with temperature alarm and automatic control system to strictly control the operating temperature of each equipment
6.4 Set up the safety device of adsorption bed, when the adsorption box high temperature pressure is too high, explosion-proof pressure relief, at the same time, the system automatically alarm.
6.5 PLC automatic control system, automatic control of the operation process, and record the operation data.
6.6 The system is equipped with multiple security protection measures, combined with automatic protection and alarm.
Our factoryOur ServicePre-Sales Service
* Inquiry and consulting support.
* View our Factory.After-Sales Service

* Training how to instal the machine, training how to use the machine.
* Engineers available to service machinery overseas.Packing & DeliveryFAQ
1.What is the company's packaging details?
The normal package is wooden box(Size: L*W*H). If export to european countries,the wooden box will be fumigated.If container is too tigher,we will use pe film for packing or pack it according to customers special request.2.What are the advantages of the company's equipment?
(1). The equipment has advanced design principle, unique material, stable performance, simple operation, safe and reliable, no secondary pollution. The equipment covers an area of small, light weight.
(2). The use of a new type of activated carbon adsorption material - honeycomb activated carbon has advantages of thermodynamic properties, low resistance, low consumption, high adsorption rate, etc , compared with the granule (bar).
(3). The catalytic combustor uses ceramic honeycomb noble metal catalyst, the resistance is small, can operate normally with the low pressure fan, not only consumes less electricity but also the noise is low.
(4). Activated carbon bed adsorbing organic waste gas can be used for desorption and regeneration of the heat generated by the waste gas treated by catalytic combustion. The gas after desorption is sent to the catalytic combustion chamber for purification. No additional energy is needed.contact us