2018 new designed ultrasonic water level sensor

2018 new designed ultrasonic water level sensor
Product Description
Features
1. Compatible with the many kinds of this similar product.
2. High sensitivity
3. Readings can occur up to every 33mS(30Hz) within 3meters or occur up to every 80ms(12.5Hz) within 10meters.
4. Free run operation can continually measure and output ranger information
5. 9V-28V supply with very low average current draw
6. Multi-kind output type such as analog (40-20mA, 0/1-5V, 0/1-10V), RS485, Can bus.
7. Sensor operates at 40 KHz, 112 KHz, 175 KHz, 300 KHz, 1 MHzBrief introduction of 2018 new designed ultrasonic sensor
This sensor provides very short to long-range detection and ranging, in a compact, robust PVC or stainless steel housing, designed to meet IP67 water intrusion. The power 9.0V-28V operation detects objects from 0.1meters to 10meters and provides sonar range information from 0.25meters out to 10meters out with 0.001meters or 0.01meters resolution. The interface output formats included are pulse width output, analog voltage output 0/4-20mA current output, NPN/PNP output and RS485,RS232 output modbus-RTU and modbus-ASCII supported.
Parameters
General Specifications
Sensing distance 100.4000mm
Adjustment range 100.4000mm
Unusable area 0.200mm
Standard target plate 100mmx100mm
Transducer frequency about 112kHz
Response delayabout 195ms
Indicators/Operating means
LED bluePower on
LED yellow Indication of the switching state
Flashing: program function object detected
LED red permanently red: Error Red,
Flashing: program function,object not detected
Electrical specifications
Operating voltage UB 10.30VDC,ripple10%ss
Power consumption P0 ≤900 mW
Output
Output type analogue output 0.10V
Resolutionevaluation range [mm]/4000, but ≥ 0.35 mm
Deviation of the characteristic curve ≤0.2% of full-scale value
Repeat accuracy ≤0.1% of full-scale value
Load impedance 0.500 Ohm
Temperature influence ≤2% from full-scale value
Ambient conditions
Ambient temperature-25.70°C
Storage temperature-40.85°C
Mechanical specifications
Protection grade IP67
Connection Connector M12x1,4-PIN
Material HousingBrass, nickel-plated
Transducer Epoxy resin/hollow glass sphere mixture;
Polyurethane foam
Weight 60g
External synchronization
The sensor can be synchronized by the external application of a square wave voltage. A synchronization pulse at the synchronization input starts a measuring cycle. The pulse must have a duration greater than 100 μs. The measuring cycle starts with the falling edge of a synchronization pulse. A low level > 1 s or an open synchronization input will result in the normal operation of the sensor. A high level at the synchronization input disables the sensor. Two operating modes are available:
1. Multiple sensors can be controlled by the same synchronization signal. The sensors are synchronized.
2. The synchronization pulses are sent cyclically to individual sensors. The sensors operate in multiplex mode.
Internal synchronization
The synchronization connections of up to 5 sensors capable of internal synchronization are connected to one another. When power is applied, these sensors will operate in multiplex mode.
The response delay increases according to the number of sensors to be synchronized. Synchronization cannot be performed during TEACH-IN and vice versa. The sensors must be operated in an unsynchronized manner to teach the evaluation limits.
Note:
If the option for synchronization is not used, the synchronization input has to be connected to ground (0V) or the sensor has to be operated via a V1 cable connector (4-pin).
Adjusting the evaluation limits
The ultrasonic sensor features an analogue output with two teachable evaluation limits. These are set by applying the supply voltage - UB or + UBto the TEACH-IN input. The supply voltage must be applied to the TEACH-IN input for at least 1 s. LEDs indicate whether the sensor has recognized the target during the TEACH-IN procedure. The lower evaluation limit A1 is taught with - UB, A2 with + UB.
Two different output functions can be set:
1. Analogue value increases with rising distance to object (rising ramp)
2. Analogue value falls with rising distance to object (falling ramp)
evaluation limits may only be specified within the first 5 minutes after
Power on. To modify the evaluation limits later,
the user may specify the desired values only after a new Power On.
TEACH-IN rising ramp (A2 > A1)
- Position object at lower evaluation limit
- TEACH-IN lower limit A1 with - UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A2 with + UB
TEACH-IN falling ramp (A1 > A2):
- Position object at lower evaluation limit
- TEACH-IN lower limit A2 with + UB
- Position object at upper evaluation limit
- TEACH-IN upper limit A1 with - UB
Default setting
A1: unusable area
A2: nominal sensing range
Mode of operation: rising rampProduction FlowCasesPackaging & ShippingCertificatesCompany Information
Xi'an Kaciseis certified by ISO 9001-2008, GJB 9001B-2009, CE, intrinsic safety explosion-proof and isolated safety explosion-proof, etc. which assure our products are conform to the international standards.
We have been specializing in manufacturing pressure, level and flow measuring instruments and related products for 10 years. We have experienced technical and management personnel, through the efforts of our entire staff, we have become a professional measuring instrument manufacturer and solution provider. And we are continuously trying to improve product quality.
Currently, Kacise sensor is already exported to America, Spain, Australia, Chile and 20 other countries and regions, and received many favorable feedbacks. Our overseas distributers are also increasing. We regards “reasonable prices, efficient production time and good after-sales service” as our tenet, and hope to cooperate with more customers for mutual development.Our ServicesYour inquiry will be replied in 24hours.Well-trained and experienced staffs to answer all your enquires in fluent English.OEM&ODM, we can help you to design and your request will be put into product.Distributorship are offered for your unique design and some our current models.Protection of your sales area, ideas of design and all your private information.Discounts are offered based on order quantities.We provide paid repair services for meter damages not arising from manufacturing quality issues or meter damages not within the scope of warranty.FAQ
1.Q: What information need to be provided to choose the suitable model?
A:Please provide us: , range,, ,
,so we can choose model and quote for you quickly.
2.Q: Are you a trade company or a manufacturer?
A: We are an ISO approved manufacturer specialized in level and flow measuring instruments.
OEM & ODM service are available. Welcome to visit us.
3.Q: What is your MOQ?
A: To start our cooperation, sample order is acceptable.
4.Q: What is your delivery date?
A: The delivery date is about 3-15 working days after receipt of payment.
5.Q: What is your payment terms?
A: We support T/T, PayPal and Trade Assurance.
For mass production order, it is 30% deposit in advance and 70% balance before shipment.
6.Q: What is Trade Assurance payment method:
A: It’s a free service which can protect your orders from payment to delivery.
And we now have USD104,000.00 of caution money to assure your orders.
7.Q:Do you have a warranty?
A: Yes, we have the warranty of 12 months.