Surgical wound care of the most popular skin stapler wound surface

Product Description
model
LK-I LK-LL LK-LLL LK-LV LK-V
product composition
Medical tape Polypropylene (PP) zip fastener Release paper (or release film)
Sterilization period
Two years
storage
The packaged product should be protected from strong light, stored in a relative humidity not exceeding 100 molecules,
non-corrosive gas, cool and dry well-ventilated room.
Note：Set of four for $ 140 each
[Instructions](-) Preparation before suture(1) If layered sutures are required, subcutaneous layered sutures should be performed first using standard methods to reduce wound tension and allow better overall wound healing. (2) Apply standard methods to clean the wound surface, so that the skin surface around the wound should be clean, dry, and free of oil and grease to ensure that the adhesive surface of the snap-on skin suture device is firmly adhered to the skin.(3) Arrange the wound skin margin so that the wound skin margin is as close as possible.(4) According to the size of the wound, determine the number of pull-type skin staplers, and the distance between each set of pull-buttons should be less than about 2mm..
(Say) suture the wound (Figure 1, 2, 3, 4)(1) Open the sterile packaging bag.(2) Grasp the two straps of the pull-type skin suture device by hand and peel them off the release paper (or film) bottom plate.(3) The tape parts at both ends of the pull-type skin stapler are accurately placed on both sides of the skin margin of the wound. Try to bring the medical tape as close to the skin edge of the wound as possible, and gently press on the tape.(4) Pull the two side straps to tighten the pull-type skin suture until you hear a "click" to lock the lock, making the wound tight.(5) Cut off the excess cable tie.(6) If necessary, continue to place the next skin buckle.(=) After stitching(1) Clean up the wound after suture.(2) The dressing can be used to cover the outside of the wound to prevent external contamination.(D) Postoperative observation and removal(1) The wound condition should be observed after surgery, which can be directly cleaned, drained and treated with medicine, and gauze should be replaced to keep the wound clean.(2) After 7-10 days, the doctor will remove it according to the wound healing.

【Precautions】The ear root, armpit, elbow joint, knee joint, knuckle joint, and wounds with a surface surgery angle of less than 90 degrees are not recommended for use with snap skin sutures. ● To achieve the desired effect of wound healing, the wound tension should be minimized.● Before using the buckle type skin stapler, the surface of the wound skin must be cleaned, blood stains and disinfectant must be cleaned, and the surrounding of the wound should be kept as dry as possible, otherwise the adhesion between the buckle type skin stitcher and the skin will be reduced.● When applying medical tape, try to get close to the skin edge of the wound. Due to the strong adhesive force of medical tape, try to avoid the mechanical tension of the skin pasting surface due to the tension of the wound, resulting in tension blisters on the skin.● After the medical tape is applied to the wound, it cannot be repeatedly peeled off and re-applied, otherwise the initial adhesiveness of the medical tape will be destroyed and the adhesion to the skin will be reduced. If necessary, replace it with a new skin buckle.●. If the dressing covered by the post-operation is wet with wound bleeding, exudate or secretion, the clean and dry dressing should be replaced in time to avoid affecting the stickiness of the tape. If necessary, when the tension of the incision has been reduced, the assistant can replace the pull-type skin suture with the assistant pushing inwards with both hands to protect the incision.● Snap-on skin suture device is sterilized with ethylene oxide, marked with "sterilized" logo, and marked with (STERILEEO) logo.The snap-on skin suture device is a one-time use product. It is forbidden to use the damaged package and destroy it after use.
Semi-Automatic PET Bottle Blowing Machine Bottle Making Machine Bottle Moulding Machine
PET Bottle Making Machine is suitable for producing PET plastic containers and bottles in all shapes.