Extra Glossy, Waterproof and Smooth Premium Skim Coat Plaster Cement and Wall Putty

Product DescriptionTPI M650P Super Premium Skim Coat (Extra Glossy, Waterproof and Smooth Premium Skim Coat Plaster Cement and Wall Putty)
Ready-made mortar.Super Premium Skim Coat for Thin Wall Rendering (Extra Smooth High Gloss Surface) M650Pis used as thin layer plastering to give fine finish to decoration works. It can be used for restoration and repair of cracked surface, coarse plaster works and hair line cracked surface by applying it with trowel to get very fine smoothen surface. It is unnecessary to paint on the surface of its smooth natural color, but if customer wishes, it can be coated by paint to desire hue.
SCOPE OF USECan be applied on concrete walls. Or plaster walls, such as the wall plastered with M100, M100C, M200 or M210, etc. can also be used wall posts. To cover cracks or crevices.RAW MATERIALTPI Portland Type 1 Cement according to ASTM C-150 and TIS 15-2555Chemical additives such as additive properties of water. Additives, adhesives, etc.Fine limestone crushedHOW TO USE
1. Wall preparation
- In cases where the wall is smooth, the M650P can be plastered without any plastering.
- If the wall is plastered with very rough surface, such as concrete wall, use M100C pre-plastering. Try to smooth the surface evenly. And wait for the plaster to dry completely. Made with M650P
2. Using
- Mix mortar M650P with water using a mortar ratio of 1 bag (15 kg) per 6 - 7.5 liters of water, adding the water gradually and stirring homogeneously. Without resting the plaster to the water.
- Plaster M650P with polished steel trowel By thin-walled plastered up the floor one at a time when the plaster. Apply in the same way until the desired thickness (about 1-2 mm).
- Before painting, fine sandpaper can be used to smooth the surface.
Thickness of plaster The plastered area is 20 kg. The amount of cement per 1 sq.m. 1-2 mm./ 10sq.m./ 15 kg.Company Information
TPI Polene is one of the major manufacturers and distributors of cement products and mortar cement under the brand name “TPIPL”. The plants are located in Saraburi province. All the Company’s cement products meet the ISO/TIS certifications of industrial standards, ASTM Industrial Standards and the EU Industrial Standards. TPI Polene was the first cement manufacturer in Thailand to be awarded ISO 9002 Certification from the International Standard Institute, for surpassing industrial and environmental protection standards. This has enabled the Company to export cement to the state of California, where surrounding communities are highly aware of environmental conservation.
TPI Polene was also the first cement manufacturer to be awarded the Carbon Label for both Portland cement and the mortar cement products. The Carbon Label demonstrates that the producer has submitted data to show that it has significantly reduced carbon dioxide (greenhouse) emissions, which cause global warming.
The Company currently operates four cement production plants with total production capacity of 13.5 MTPA (Cement line 4 become commercially operational in early 2016), using technologically advanced machinery, and is strategically located, adjacent to both a limestone quarry and an efficient transportation distribution network, which reaches throughout the country. This gives the Company its low-cost competitive advantage. Besides, TPI Polene Group operates Waste Heat Recovery Power Plants, which generate electricity from waste heat emitted from TPI Polene’s 4 cement production plants and/or uses Refuse Derived Fuel (RDF) as fuel to generate electricity in its RDF-fired power plants. As a result, TPI Polene Group become a power plant operator in Thailand, with the largest waste-to-energy power plant operations in the country, a renewable energy to enhance environment.
Further information about our company:Visit Our MinisiteFAQ
Q: What is the Minimum Order Quantity (MOQ)?
A: At least 1 full container load
Q: What is the lead time?
A: At least 14 days