Waterproof Cement Hydraulic Concrete Water Plug Cement

Product Description
TPI M680 (Mixed Hydraulic Cement) (Waterproof Cement Hydraulic Concrete: Water plug cement)Water Plug Cement (Waterproof Cement Hydraulic Concrete: Water plug cement)
TPI M680 is mixed hydraulic cement with very fast in setting time and it can be applied both under Water and in the air. It sets within 3-5 minutes and suitable for holes or cracks in concrete or masonry walls, swimming pool, leakage pipe and it can set even under running water and able to stop active water leakage. It can be also used for the quick repair to walkway and anchoring bolts on concrete surface.PREPARATION PROCEDURESurface must be clean and structurally sound and remove all dirt and loos material. Chip the crack to at least 1 cm. depth then cleaning and saturate the surface with water before plugging with mortar.Mix TPI M800 with clean water at the ratio 4:1Rapidly mix all together well and it should it should be used within 3 minutes.
Avoid reuse the hardened cement mixture.
Remark: When mixing 1 kg of water plug (TPI M800) with the ratio water volume amount is 500 cm2APPLICATIONIn case of repairing active water leakage, place the TPI M680 Mixture in your hand until cement begin to setting then apply it in the leaking region and keep pressing for 3-4 minutes and clear the excess material around the surface.In case of repairing the crack concrete, place TPI M680 onto the crack with trowel then clear excess materials around the surface. Cure it by spraying with water or covering a damp cloth for 3 hours.In case of plugging the anchor bolt holes in concrete, holes’ width must be at least 1 cm. then fill and press cement firmly with trowel and clear excess materials before cement sets.
Suitable for Repairing the leak, Stop water leaking immediately and special Fast setting.Company Information
TPI Polene is one of the major manufacturers and distributors of cement products and mortar cement under the brand name “TPIPL”. The plants are located in Saraburi province. All the Company’s cement products meet the ISO/TIS certifications of industrial standards, ASTM Industrial Standards and the EU Industrial Standards. TPI Polene was the first cement manufacturer in Thailand to be awarded ISO 9002 Certification from the International Standard Institute, for surpassing industrial and environmental protection standards. This has enabled the Company to export cement to the state of California, where surrounding communities are highly aware of environmental conservation.
TPI Polene was also the first cement manufacturer to be awarded the Carbon Label for both Portland cement and the mortar cement products. The Carbon Label demonstrates that the producer has submitted data to show that it has significantly reduced carbon dioxide (greenhouse) emissions, which cause global warming.
The Company currently operates four cement production plants with total production capacity of 13.5 MTPA (Cement line 4 become commercially operational in early 2016), using technologically advanced machinery, and is strategically located, adjacent to both a limestone quarry and an efficient transportation distribution network, which reaches throughout the country. This gives the Company its low-cost competitive advantage. Besides, TPI Polene Group operates Waste Heat Recovery Power Plants, which generate electricity from waste heat emitted from TPI Polene’s 4 cement production plants and/or uses Refuse Derived Fuel (RDF) as fuel to generate electricity in its RDF-fired power plants. As a result, TPI Polene Group become a power plant operator in Thailand, with the largest waste-to-energy power plant operations in the country, a renewable energy to enhance environment.
Further information about our company:Go to MinisiteTrade Shows
Recent Exhibition in Thailand called "Thailand Industry 4.0"
TPI M501 is high bond adhesive mortar for floor and wall applications for both outdoor and indoor. It can be applied for large tile, fiber board, wood flooring and parquet. It performs extremely high bond adhesive strength on concrete surface and allows to laying new tiles on the old tiles. During tiles paving, it gives adequate time for tile adjustment. Therefore, M501 is to use and save time and money.
Go to M501
Extra High Bond Adhesive mortar cement for very large tiles ( Marble tiles and Granite tiles) (M503)
TPI M503 is an adhesive mortar for fixing large size ceramic tile, marble tile, granite tile on wall and floor for swimming pool tile both interior and exterior. Provide high adhesive bonding strength and suitable for fixing large tiles and low water absorption ceramic tiles. It can be applied on smooth concrete surface. Setting time is so adjusted that ater mixing, it gives adequate time for the tile adjuestment. It is easy to apply. It saves time and money.
Go to M503
Multi purpose repair mortar (M600)
TPI M600 is suitable for repairing the small areas such as cracking area, wall scaling, breaking/ drilling marks, leakages, ceramic tile repairing etc.
Go to M600
Sealant (M611)
High flexibility and no shrinkage. Or for repairing materials with cracks, leaks, longer service life than other types of grout materials. It can be adhered to many materials such as fiber cement, artificial stone, aluminum, metal, tile, gypsum board, ceramic and UPVC etc. can be used both indoor and outdoor. Through secure use. Can be painted over not slip.
Go to M611
Super Fix Poly-urethane Adhesive Compound (M612)
TPI Super M612 is specially engineered Poly – Urethane adhesive coming in two separate tins to be mixed before use. This adhesive compound is a quick action adhesive to fix metal parts such as light steel section and fiber boards on concrete wall or columns.
Go to M612