Co Convert To Co2 Catalyst Co Convert To Co2 Ceramic Honeycomb Catalyst Ceramic Honeycomb Catalyst

CO Removal Catalyst (four products)
Production Introduction
1. CAS-KR-Y01-F CO removal catalyst)2. CAS-KR-Y01K-F oven exhaust gas purification catalyst
CAS-KR-Y01K-F oven exhaust purification catalyst is suitable for baking oven, fireplace and other equipment used for the catalytic combustion of unburned CO, purification effect is very good.
3. CAS-KR-Y01M-F mosquito magnet catalyst
CAS-KR-Y01M-F mosquito magnet catalyst belongs to high-tech material products, with the liquefied petroleum gas catalytic oxidation to simulate human CO2 function to attract mosquitoes to mosquito catcher, at the same time,heating and oxidation generated can be used to produce electricity for the mosquito catcher, the product non-toxic harmless, environment friendly products, mainly used in luxury mosquito eradication machine.
4. CAS-KR-T02-K CO normal temperature removal catalyst
CAS-KR-T02-K CO normal temperature removal catalyst is using active alumina as carrier, and a unique addition of rare earth materials, with a high content of noble metal Pd, Pt as active component prepared.Can be used for CO at normal temperature within an enclosed environment under the mine rescue capsule / refuge chamber and eliminate, can also be used in submarine cabin, fire mask, CO2 laser, gas shower device with a small amount of CO is required to eliminate in the occasion.The catalyst at normal temperature (≥ 15 °C), air humidity below 90%, space velocity of 0.5 x 104H? 1, 20min CO can be converted, the residual amount of CO ≤ 23ppm, single cycle time is not less than 24 hours, after simple regeneration can be reused for more than 3 cycles.
1.1. Operation condition & Technology properties
No
Test item
Technology parameter
Carrier: cordierite and composite alumina with various specs
1
Space velocity
≥3x103h-1
2
Initial ignition temperature
100°C-150°C
3
Optimal service temperature
180°C-200°C
4
CO removal ratio≥ 98%5
Service life
≥ 2 years
5
CO outlet content
<5ppm
6
Bulk density
0.68±0.05g/mL
7
Crushing strength
≥ 14 MPa
8
Coating component
≥ 10.0%
9
Activity component
0.08%-0.2% (also depends on your demand)
10
Expulsion ratio
<1%
11
Appearance
Usually is light yellow (would be grey after pre-reduction)
12
Packing
Moisture-proof
13
Suggested loading height/diameter
Honeycomb type 4:1;2:1particle 1:1
(CAS-KR-Y01K-F type carbon monoxide removal oven catalyst product pictures.) 2.1.CAS-KR-Y01K-F Operation condition & Technology properties
No
Test item
31.75x6.35
31.75x12.8
1
Space velocity
≥3x103h-1
2
Initial ignition temperature
200°C-250°C
3
Optimal service temperature
250°C-400°C
4
Service life
≥2years
5
CO outlet content
<4mg/m3
6
CnHm outlet content
<5mg/m3
7
Bulk density
0.68±0.05g/mL
8
Crushing strength
≥12 Mpa
9
Rupturestrength
≥2 Mpa
10
Coating component
>10.0%
11
Activity component
≥0.1%
12
Expulsion ratio
<1%
13
Appearance
Usually is light yellow & red(would be grey after pre-reduction)
14
Packing
Moisture-proof
2.2. The purification principle and characteristics of the CAS-KR-Y01K-F oven exhaust catalyst
The harmful exhaust CO and unburned hydrocarbons CnHm easily generated in the barbecue process oven equipment.After install the exhaust gas purification catalyst oven, under the action of a catalyst, in the process of exhaust gas temperature rising in the oven, oven exhaust further temperature catalytic oxidation, can produce emissions of CO2 and H2O , so that CO and CnHm can reach the discharge standard,and the oven exhaust purification as the purposes. CAS-KR-K01-F oven exhaust gas purification is in the conditions of catalyst at a temperature of 250~400 °C, airspeed (0.3~1) x 104h−1 , the purified gas, CO and non-methane hydrocarbons content can be reduced to below 4mg/m3; the catalyst can be repeatedly recycled, the mechanical strength is good so that the service life can more than 2 years. 2.3. The points for attention in useof CAS-KR-Y01K-F oven exhaust purification catalyst
Oven exhaust catalyst need preheat to 200~250 °C activation first, and then run the oven gas to be treated, the better the operation temperature over 300 °C, the reaction conditions of 1.5~3.0 * 103h-1 CO in exhaust can be eliminated to below 0.5ppm, non-methane hydrocarbons can be reduced to below 1 ppm; the highest heat-resisting temperature is 750 °C (if the combustible gas concentration is high,it need to be matched with cooling system, prevent catalyst sintering).
3.1. CAS-KR-Y01M-F mosquito magnet Catalyst specifications
NO.
Test item
specifications
40.89x6.35
Carrier specifications40.89x9.652
40.89x25.4 1
Light display time
<900s
2
The outlet CO concentration
<0.5mg/m3
3
Service life
≥2years
4
Bulk density
0.66±0.05g/mL
5
Compressive strength
≥12MPa
6
Carrier specifications
According to customer requirements
7
The coating layer of the load
>8%
8
Fall off rate
<1%
9
Appearance
Shallow brown
10
Packing
Moisture seal
CAS-KR-Y01M-F mosquito magnet Catalyst product pictures 3.2. Principle of special CAS-KR-Y01M-F mosquito magnet Catalyst)
Mosquitoes are issued by the body of carbon dioxide atmosphere to find people, when they feel the carbon dioxide gas flows immediately they will flew to the air stream; mosquito magnet is a machine that using the liquified petroleum gas to run produce the simulation of human respiratory carbon dioxide concentration and catch the mosquito ; which produce simulated human respiratory carbon dioxide concentration and the elimination of carbon monoxide as core components is CAS-KR-Y01M-F type catalyst for mosquito magnet. 3.3. Characteristics of CAS-KR-Y01M-F catalyst for mosquito magnet
CAS-KR-Y01M-F mosquito magnet catalyst belongs to high-tech material products, with the liquefied petroleum gas catalytic oxidation to simulate human CO2 function to attract mosquitoes mosquito catcher,at the same time, heat and oxidation generated waste heat can be used to produce electricity for the mosquito catcher used.The product non-toxic harmless, environment friendly products, mainly used for luxury type mosquito killing machine, can also be used in oven, fireplace and industrial CO and VOC gas catalytic oxidation.
3.4. Note of using CAS-KR-Y01M-F catalyst for mosquito magnet
The installation to use inorganic material of high temperature resistant pad, do not need to disassemble the moisture-proof seal after long-term , catalyst wetting caused failures by 110 °C drying or calcined at 500 °C regeneration.
4.1. CO normal temperature Removal CatalystTechnology propertiesTest Item
2-3(mm)
Composite AL2O3 specification 3-4(mm)
4-5(mm)
1
Airspeed
>0.5x104h-1
2
(using temperature)
Nomal temperature
3
Service life
≥24h
4
Bulk density
0.65±0.2g/ml
5
Crushing strength
≥60N/Φ2-3(mm)
6
Removal CO depth
≤23.0ppm
7
Resistance to humidity
≤90%
8
Active component load
≥1.0%
9
CO removal rate
≥95%
10
Appearance
Dark gray
11
Packing
Moisture seal
12
Recommended to install the ratio of height to diameter
≥1:1
4.2. The operation and maintenance of CAS-KR-Y01-1 carbon monoxide nomal temperature removal catalyst
CAS-KR-Y01-1 carbon monoxide normal temperature removal catalyst without activation, without preheating, at normal temperature in air purifier used directly.Placed in front of 1:1 catalyst volume when using active carbon or alumina molecular sieve catalyst for moisture.The vacancy please seal packaging, when opened, if damp with constant temperature of 120 °C drying after using 3h.Company ProfilePackaging & ShippingContact us